Introduction
The Serpent Cobra
Buggy 2.2 is a result of continuous development and intensive cooperation with
the key team-drivers.
The changes for the 2.2 version are not very big,
but very important to make you go around the track easier and faster.
-
Upright buggy 1/8 V2 (2) - Wheelaxle buggy v2 (2) - Driveshaft buggy 98mm
(2) - Wheel-axle boot rubber (2) - Antiroll bar front 2.3mm
and
below developments are continued also in the 2.2 version. - plus 4 chassis:
the hard anodised chassis is 4mm longer in the rear, creating a more stable
rear end, especially better on tracks with short bumps and rough surface. The
great handling on smooth, flat surfaces remains ! - longer alu rear brace:
the longer alu brace also helps to make the rear end more stable. The shorter
nylon or alu version can also still be fitted. - longer rear central shaft:
to suit the longer chassis a longer rear central shaft is needed (which is
actually the same as the one used in Cobra buggy 1.0 ) - hard coated
shockcaps: the hardcoated aluminium shockcaps can withstand the rigors of
crashes better - aluminium 14 dgr casterblocks The Cobra buggy has a lot of
steering already which makes it turn very fast. The 14 degree caster blocks
help to smoothen steering out a bit, still lot of steering , but easier, less
direct, creating a more stable front end.
Chassisplate 4mm longer hard anodised chassisplate
in 3mm 7075 T6 aluminium , with machined pockets to create flex make lighter.
Kick-up angle on front for stabile landings. Countersunk holes. Slots to
locate the front and rear suspension mounts precisely. Angled sides to
increase stiffness. Laser engraved Cobra logo. Bumper
Aligned with chassis kick-up for precise landings and to protect front
suspension holder and anti-roll bar. Chassis
stiffners Aluminium longer rear stiffner, and composite front stiffner,
to give extra stiffness, but still allow some flex as
needed. Central radio / servo mount Composite radiobox which
offers good space for the steering and throttle -servo, the receiver and rx
battery. The whole assembly including linkages can be taken off easily and
fast in one go, when cleaning the car, or doing maintenance. One extra post is
added close to the servo for stability. Servo arms and linkages The
servo arms have a splined insert to have the right fit per brand. The linkages
run very clean and tight and are easy to access to modify
settings. Suspension brackets Beautifully machined 7075 T6
suspension brackets in anodized, laser angraved. Precision fit for the nylon
roll center inserts and pivot balls / pins. Steeringblocks
assembly Composite steeringblocks combined with 14 dgr black anodised
aluminium C-hubs for precise steering. Composite 10 and 12 dgr c-hubs are also
included. Spring steel wheel-axles with large size bearings and larger inner
with precision threaded aluminum wheel-hubs with offset. Flanged and serrated
wheel nuts. Front suspension Durable oversized lower
suspension arms in strong composite nylon. On the lower side the special shaped
downstops screws are mounted. The lower shock-mounting pins are secured with a
small grubscrew from the bottom. Front anti-roll bar The
ballraced front anti-roll bar system, consist of a spring steel bend wire,
which is guided through the diff-cases and runs in ballraced steel adaptors.
The wire is linked to the lower suspension arm, with a captured adjustable
threaded pivotball, for very precise and low friction operation and easy
tuning. Shocktower and bodymounts front 4.5mm thick carbon
shocktower with 5 upper positioning holes for the shocks and and 6 holes for
roll-center positions. 1 centrally located adjustable bodymount , and 2 forward
mounted adjustable bodymounts, all with flip-tops. Angled steering
system / servo saver The bell cranks are angled to reduce the angle of
difference between the total caster and steering plane. Therefore you will have
less bump steer and a truer steering Ackerman through the entire range of
suspension Ackerman plates With the design of the steering
bell cranks when changing the Ackerman you will not need to adjust your steering
tie rods. You simply will only need to adjust your end points on your
radio. Rear suspension arms Durable longer oversized lower
suspension arms in strong composite nylon. On the lower side the special
downstops screws are mounted. The lower shock-mounting pins are secured with a
small grubscrew from the bottom.
Mud-guards Superlight
polycarbonate mud guards mount to the new lower suspension arms, and will keep
dirt away from your anti-roll bars transmission and wheels. Rear
uprights v2 assembly Composite uprights with 3 upper roll-center
positions. Strong steel track-rods with L/R threading and strong balljoints to
pre-set camber. Spring steel wheel-axles with large size bearings and larger
inner ones with precision threaded aluminum wheel-hubs with offset . Rubber
dustcovers in the rear to protect the cvd system and keep the lubrication
inside. Flanged and serrated wheel nuts to guarantee that you will not loose a
wheel nut in a race. Rear anti-roll bar The ballraced front
anti-roll bar system, consist of a spring steel bend wire, which is guided
through the diff-cases and runs in ballraced steel adaptors. The wire is linked
to the lower suspension arm, with a captured adjustable threaded pivotball, for
very precise and low friction operation. Shocktower rear
4.5mm thick carbon shocktower, integrated into the rear section for extra
stiffness, with 5 upper positioning holes for the shocks and 6 holes for
roll-center positions. Wingmount and bodymounts
rear Composite rear wing, with strong nylon adjustable rear bodymounts on
wide body-support bridge located far enough to the rear, to support the bodies
in best way. Captured pivot pins and balls and bolted hinge pins.
All spring-steel hinge pins are either captured or bolted in place and made in
spring-steel quality. This insures your chances to finish an hour long main
event, while battling for the lead. This relieves stress on the hinge pin when
adjusting the kick up, or anti squat. Your pin is free to rotate to any angle
without binding. Shockabsorbers big-bore 16mm Hard Teflon
coated threaded shockbodies with 4mm shock-rods. Hard anodized aluminium screw
on hard anodised shock-tops with Serpent laser engraving. Pre-load adjusters
with o-rings inside. Shocks use large diameter membrames and large diameter
o-rings and bushings to create a supersmooth and leak-proof package. Large
diameter pistons are held in place by a nut on the polished shock-rods tops.
Open type spring retainer to let dirt out easy. The shock-shafts are protected
by rubber boots. RCM shock springs Short type colorcoded
shock springs are supplied for the 1st standard set-up Springs are grinded flat
top and bottom, and checked individually for tension and length.
Compact geardifferentials Very compact gear differentials with very
smooth metal sintered gears, and steel shaft. Perfect sealing case with special
gasket and o-rings. Very light and durable outdrive cups in spring-steel.
Hardened spring-steel diff-coupler 13T with connector running in 2 oversized
bearings . Drive ratio 4.3:1. This drive ratio will provide amazing
acceleration combined with the low vehicle weight. It is a sure win, to help
improve fuel mileage Front and rear cvd-sets Both front and rear
captured driveshafts are being used with CVD system. Durable yet light spring
steel engraved driveshafts with hard steel pins. Spring steel
transmission parts The front and rear thin but strong spring steel cardan
shafts connect the differentials . Throttle and brake lever ball
cups Helps provide consistent pulling on the brake lever or carburetor if you
do not have the linkage perfectly aligned.
Piston Braking
system Provides more stopping power than you could have ever imagined before
with a whole lot less servo power. Also is fully adjustable with 3 types of
pistons, solid, O ring type, spring type. In turn you can adjust your bias or
braking feel to your liking in more ways than ever before.
Fiber Glass
disc brakes Fiber Glass brake disks with oversized front disk.
Brake
plate springs Will keep the plates spread open to insure un-wanted dragging
of the brake discs.
Racing clutch 4 - shoe Allows you to mix and match
shoe materials evenly in pairs. Also provides more surface area contact to
insure the engagement. 4 carbon shaped shoes are standard ( alu ones
optional).
Coil exhaust wire and alu mount Helps aid in the front to
back movement of the pipe when chassis flex occurs. Helps prevent damage to your
exhaust gaskets.
Engine mount Machined 7075 T6 aluminium engine
mount, with side cooling-fins.
Fueltank 125cc Splash basin on tank
top, self centering Fuel tank seal, The fuel tank seal is angled to self guide
its way into the bore of the tank. At the same time will provide a seal on the
chamfered and flat edges of the seal, providing consistent engine performance
from one pit stop to the next. Built in tank splash guard which helps prevent
fuel from splashing onto your air filter in the event of an overly excited pit
man.
Fueline and stoppers Kit included topqualiity soft silicone
fuelline to connect to tank, car and pipe, and also includes small composite
stoppers to close yr fuelline when taking out tank, engine and or
pipe.
Tank with swiveling nipple and floating clunk. With the
swiveling nipple you are able to adjust the angle at which you want you fuel
line to travel. At the same time the floating clunk helps when you go upside
down. The clunk by gravity will fall back into the fuel, utilizing the
flexibility of the silicone fuel tubing.
Low profile air
filter Centralized air filter design to minimize cab width and height.
Flexible rubber boot combined with strong nylon case to support the foam
elements. Excellent dense foam airfilter elements to keep your engines clean
inside.
Body Serpent cab forward Avenger body, with film and masking
tape is included in the kit.
Rear wing: Low version strong rear white
aero rear wing is included for great downforce and straight line
stability.
Oils and grease The shock-oil, diff oil and some grease
is supplied to meet the standard set-up. Manual and
set-up Full color manual with easy to follow assembly steps, exploded
views for easy spares ordering, a blank and standard set-up sheet for a good
start set-up. Decals Black and white promo body-decals ;
Serpent generic and Cobra ones. Packing Parts are packed
according to the steps explained in the manual. Service and
Support The Serpent distributor, dealer or agent is your source for more
info, but also the Serpent website and the member section and the Youtube
channel provides lots of information. Needed to complete the
car: - radio and receiver - .21 gaspowered engine and
pipe-set - fuel with 16% or 25% nitro and fuelbottle - wheels and
tyres - tools - paint - starterbox,
glowstarter - charging equipment |