E2016 - MBX7R ECO 1/8 electric Buggy Kit (off road): |
|
|
Mugen
concentrated on the making the suspension on the MBX7R ECO even better with new
16mm bodied front and rear racing shocks. These bigger bore shocks will improves
stability in bumps which will handle all the power that this electric buggy will
produce. The
7R ECO chassis has been changed to increase strength and give the ECO buggy a
better feeling on all indoor and outdoor racing surfaces.
|
|
|
|
|
|
The 7R ECO has
a re-designed front hub carrier in which the position of the front axle has been
changed to a trailing axle position. This new front hub carrier in conjunction
with a new designed steering ackerman plate will greatly improve steering input
of the 7R ECO. The front upper suspension arms have been shortened 1.6mm to
allow for more camber adjustability. The front and rear drive train (diffs to
wheels) have been changed and improved with new designed universal drive
shafts. These drive shafts will greatly improve the feel of the ECO buggy on
bumpy surfaces. The use of the universals will make the overall drive train
much smoother and will spin with less friction. The new wing mounts will allow
the wing to be moved closer to the shock tower and will increase rear traction
and jumping abilities. |
|
|
|
|
|
The MBX7R ECO is equipped with a specially designed battery tray
which will accept either 2-2 cell LiPo batteries in a staggered mounting
position for optimum weight distribution or a single 4 cell battery
location...the choice is yours! A specially designed motor mount which has been
beefed up so you can run bigger and fast electric motors without losing gear
mesh or without the flex which causes motor or mount breakages. There is a
heavy duty sliding motor mount that is anchored down with 4mm screws for extra
strength.
All
these new improvements on the MBX7R ECO will make the ultimate 1/8 electric
buggy. The 7R ECO will be available in December 2014.
|
|
|
|
|
MBX7R ECO
Features: |
|
|
|
|
- Heavy duty aluminum motor mount housing
A |
- Heavy duty aluminum motor mount
B |
- Lightweight conical gears |
- Straight cut conical and ring differential
gears |
- Specially designed front upper and rear
lower suspension arms, front hub carriers, |
rear suspension arms and hub
carriers |
- Fully adjustable steering with new geometry,
servo saver and ackerman plate |
- Front/Rear 16mm hard anodized threaded shocks with
3.5mm shock shafts and slim rubber |
boots |
- 3mm A7075 hard anodized chassis |
- 5mm A7075 aluminum front shock
tower |
- 4mm A7075 aluminum rear shock
tower |
- 5mm A7075 aluminum lower suspension mounts
for optimized geometry |
- Stylish cab forward body |
- Re-designed wing mount and high-down force
wing |
| |
|
|
|
New parts on the
MBX7R ECO |
|
|
|
- |
|
E2129 Front Upright |
|
|
A new designed front hub carrier that incorporates the
front universal to be in a trailing axle position. A new universal (E2218) is
used with this hub and it uses an 8mm x 16mm ball bearing. |
|
|
|
- |
|
E2131 Rear Upright |
|
|
The rear hub carrier has been
modified to allow for use of an 8mm x 16mm ball bear which is required for the
new (E2219) universal shaft. This hub carrier will also allow the use of the
15mm x 21mm ball bearing too. This hub carrier can be used for either the MBX7R
or MBX7. |
|
|
|
- |
|
E2132 Front Upper Arm |
|
|
The front upper suspension arm has
been shorten 1.6mm. This will allow the use of the E0161 spacer between the
pillar ball and the upper arm. This will allow for the same camber on each side
of the buggy. |
|
|
|
- |
|
E2133 Rear Lower Arm |
|
|
The suspension arm has been
modified to allow for clearance so the new E2219 universal doesn’t rub the arm.
This arm will work on either the MBX7R
ECO
or
MBX7 buggy. |
|
|
|
- |
|
E2218 Front Universal Shaft |
|
|
A new design universal drive shaft
set for the front of the MBX7R
ECO. The
E2129 front upright must be used with these universals as they require an 8mm x
16mm ball bearing. The length of the drive shaft is 91.5mm. |
|
|
|
- |
|
E2219 Rear Universal Shaft |
|
|
A new design universal drive shaft
set for the rear of the MBX7R
ECO. The
E2131 rear
upright
must be used with these universals as they require an 8mm x 16mm ball bearing.
The length of the drive shaft is 89.5mm. |
|
|
|
- |
|
E2314 Steering Plate |
|
|
The new steering ackerman plate
has 5 adjustment holes for maximum steering adjustability. |
|
|
|
- |
|
E2408 Wing Stay |
|
|
A new wing mount that can move the wing forward maximum 10.5mm to
improve traction and overall feeling of the buggy. |
|
|
|
- |
|
E2409 Stone Guard |
|
|
|
|
|
The sides of the stone guard are
changed to fit the new chassis. |
|
|
|
- |
|
E2411 Chassis |
|
|
The side angle of the chassis has been changed to increase chassis
strength. This will allow for a better feeling on all surfaces. |
|
|
|
- |
|
E2528 Front 16mm Shock
Set |
- |
|
E2529 Rear 16mm Shock
Set |
|
|
New 16mm Front/Rear shocks which will greatly improve stability in
bumps and jumps
| |
|
|
|
Differentials Oils:
|
|
|
Front - 7,000 wt Oil
(B0323) Center - 7,000 wt Oil (B0323) Rear - 3,000 wt Oil (B0321)
|
|
Shocks, Springs, and Sway
Bars: |
|
Front: 550 wt Oil (B0333) / φ1.5
L75/7.75T Spring (E0573) / φ1.3 8H Piston (E2525) / φ2.3mm
(E0164) Rear: 550 wt Oil (B0333) / φ1.5 L86/8.0T Spring (E0577) / φ1.3 8H
Piston (E2525) / φ2.7mm (E0168) |
|
|
Download: |
|
♦ Parts List 453 KB ♦ Setup Sheet 204KB ♦ Instruction Manual 12.2MB ♦ Kit bag details 1.78MB |